Sc coil split obsidianwire with 60s switch
Easiest install ive ever done ...little bit of fiddling because its a les paul but itwas really very easy and the guitar plays beautiful couldnt be happier...super quick delivery....thanks tone lounge
ObsidianWire
Les Paul - Custom SC (Split Coil) - 15% OFF
NZ $199.00
NZ $169.00
- Shipping:
- Calculated at Checkout
Description
Reviews
Additional Info
Description
KEY FEATURES:
✔ Coil Splitting (Get Strat or Tele like tones from your LP)
✔ Improved Clarity
✔ Smoother Volume & Tone Control
✔ Includes Pro-Wired Switch
✔ Fits Gibson Les Paul
✔ Fits Epiphone Les Paul with adjustments
SUPER EASY, SOLDER-LESS INSTALL
All Obsidian Pro-Wired Electronics are super easy to install, and allow for solder-less pickup changes with Obsidian Plug, Play & Enjoy connectors.
Split your humbuckers into single coils for classic, low output spank, and back again with a tap of the volume control
The Obsidian Wire Custom SC gives you greater tonal diversity, through the power of inbuilt coil splitting switches. The upgrade comes with sturdy solder-less connectors, so it can be installed by anyone.
WHAT IS COIL SPLITTING?
Humbuckers are built with two coils of tightly wound copper, for low noise, and high output. Coil splitting cuts the link between the two coils, so we can play with one half of the humbucker. This essentially gives us a single coil, for traditional Stratocaster or Telecaster sounds.
BOTH SWITCHES DOWNPosition 1: Bridge Humbucker Position 2: Bridge Humbucker + Neck Humbucker Position3: Neck Humbucker |
BOTH SWITCHES UPPosition 1: Bridge Single Coil Position 2: Bridge Single Coil + Neck Single Coil Position3: Neck Single Coil |
NECK VOL. UP & BRIDGE VOL. DOWNPosition 1: Bridge Humbucker Position 2: Bridge Humbucker + Neck Single Coil Position3: Neck Single Coil |
NECK VOL. DOWN & BRIDGE VOL. UPPosition 1: Bridge Single Coil Position 2: Bridge Single Coil + Neck Humbucker Position3: Neck Humbucker |
CRYSTAL CLEAR TONE
To make your tone crystal clear at lower volumes we also include an Obsidian Wire Custom Spec Treble Bleed Mod. This prevents tone 'muddiness' at low volumes by allowing high frequencies to pass along a separate path to your amp, rather than being stopped short by the increasing resistance at the volume control.
COMPONENTS
Potentiometers: Obsidian Custom CTS 500k Pots (+/-10%) Split Shaft / 24 Spline
Capacitors: 150 Series Polyester Film 0.022uf (+/-5%)
Switch: Obsidian Select Pro-Wired Toggle Switch
Jack: Pro-Wired Switchcraft J11 Mono
COMPATIBILITY
Fits: Gibson Les Paul
Fits: MOST Epiphone Les Paul (Requires new knobs and wider holes as below)
Hole Size: 3/8" (9.5mm) mounting holes
Knobs: Use US spec 24 spline knobs only
Hole Size: 3/8" (9.5mm) mounting holes
Knobs: Use US spec 24 spline knobs only
Pickups: Works with Humbuckers and P90s, with modern or vintage braided wires.
Does NOT fit: Lefty, three pickup Les Paul, or any other guitar or Les Paul copy.
Additional Info
- Shipping:
- Calculated at Checkout
Related Products
Sale
British Pedal Co
Zonk Machine - Compact - 15% OFF
NZ $459.00
NZ $390.00
BPC Compact Series Zonk Machine MKI
This pedal is based on the original John Hornby Skewes Zonk Machine MKI pedal produced in Leeds, England, in 1965 – 1966. The Zonk machine is tonally similar to...